If you’re just getting started with a graveur laser pour métal, you’ve probably asked questions like:
“Why does my engraving look too light?»
“What settings actually work on stainless steel?»
“Am I using the right laser for this material?»
Don’t worry—I’ve been through all of that, and this article is here to help you avoid the trial-and-error spiral. Whether you’re customizing a knife, marking tools, or making gift items like bottle openers or tags, here’s what actually matters when engraving metal.
What Metals Can I Engrave?
Not all metals behave the same under a laser. Some engrave like butter, others fight back with reflection, oxidation, or inconsistent results.
Here’s a quick breakdown based on actual experience:
| Matériel | Engraves Easily? | Remarques |
|---|---|---|
| Acier inoxydable | ✅ Yes | Grand contraste, especially with black marking |
| Aluminium anodisé | ✅ Yes | Sharp contrast, no prep needed |
| Aluminium brut | ⚠️ Kinda | Light marks, better with multiple passes |
| Laiton / Cuivre | ⚠️ Tricky | Reflective—needs slower speed, puissance supérieure |
| Métaux revêtus | ✅ Yes | The coating helps laser absorb energy easily |
Conseil: If it’s shiny, plan to do more passes or lower your speed for deeper results.
Settings That Actually Work (Not Just What’s on Paper)
Forget generic charts. The real magic is in tweaking your settings based on what you’re engraving.
Here’s a tested baseline for acier inoxydable using a mid-power fiber laser (like 30W):
- Vitesse: 1500 mm/s
- Fréquence: 80 kHz
- Q-Pulse: 5
- Dot Spacing: 800
- Se concentrer: Surface facing up, carefully leveled
These settings give me dark black marks that are crisp and readable—perfect for ID tags, outils, ou des cadeaux.
💡 Pro tip: Always run a small test square first. Different finishes (brushed, polished) react differently, even if they’re the same metal.
Why Is My Metal Engraving Blurry or Weak?
Here are the most common reasons—and what I did to fix them:
1. Focus is Off
If your laser isn’t exactly at the right height, you’ll get fuzzy, underpowered marks.
Fix: Run a ramp test or use an included focus tool. Even a 1mm error can blur the engraving.
2. Dirty Lens
A dusty or fogged lens will scatter the beam, killing power.
Fix: Wipe gently with lens-safe cloth and alcohol. I do this every few jobs.
3. Too Fast or Not Enough Power
Speed and power go hand in hand. Rapide + low power = no mark. Lent + too much power = burn or distortion.
Fix: Pour le métal, start slow and raise speed gradually until the mark weakens—then dial it back.
4. Material Moved Mid-Job
Ça arrive. Even a 0.5mm wiggle ruins alignment.
Fix: Use magnets, gabarits, or strong tape to lock metal in place. Especially critical for round objects like knives or rings.
Troubleshooting Table – Quick Fix Guide
| Problem | Likely Cause | Solution |
|---|---|---|
| Engraving is too light | Speed too fast / Power too low | Slow down or raise power |
| Blurry or doubled lines | Focus off / Material moved | Re-check focus, clamp securely |
| Burnt edges / smoke marks | Power too high / Slow speed | Increase speed or reduce passes |
| Ghost images | Loose belts / wobbly material | Tighten belts and stabilize material |
| Lines not crisp | Dirty lens or bad focus | Clean lens, re-align focus |
Best Practice for Clean, Repeatable Metal Engraving
Here’s my personal checklist when setting up any new engraving job on metal:
- ✅ Secure the workpiece: Always. Vibration ruins sharpness.
- ✅ Run a focus check: Especially when changing material thickness.
- ✅ Clean the lens: Chaque 10 heures, or after smoky materials.
- ✅ Use grayscale or vector art: High-quality images = high-quality results.
- ✅ Save your settings: Build a material library so you don’t start from scratch every time.
FAQs – Real Questions I Had (and You Probably Do Too)
Q: Can I use the same settings on copper as I do on steel?
UN: No—copper reflects more and needs slower speed + puissance supérieure.
Q: Do I need air assist for metal engraving?
UN: Not always, but a gentle air stream helps keep soot off the lens.
Q: Why does my engraving look different on the same type of metal?
UN: Surface finish matters—matte, brushed, and polished all respond differently.
Q: Can I use the same machine to cut metal too?
UN: Not typically—engraving and cutting are very different in power needs. Stick to engraving unless your laser is rated for cutting thin sheets.
Graveur laser à fibre ComMarker B6 JPT MOPA
Bienvenue dans l’ère de la gravure couleur intelligente. Capacité de marquage couleur de taille compacte record, gravure Super 3D & Capacité de coupe Conception 2 en 1 Technologie de mise au point automatique Gravure SpeedMax™ de 15 000 mm/s Précision HD 8K Écran tactile LED intelligent
Final Thoughts – Choosing the Right Laser Engraver for Metal Projects
If you’re serious about metal engraving—whether it’s for hobby use, personnalisation, or even a side business—the right setup makes a huge difference.
Start small: pick one metal (like stainless), dial in your settings, and go from there. As you get more confident, try anodized aluminum, then experiment with copper or titanium if you’re using a MOPA-capable machine.
One machine, dialed in correctly, can do more than you think. Just don’t expect magic on Day 1—it takes a few test runs to hit that sweet spot.