Освоение стеклянной гравировки с ультрафиолетовым лазером: 30,000 Тесты, чтобы вам не нужно было

Glass is notoriously difficult to engrave. It’s unforgiving, unpredictable—and often ends in cracks, chips, or outright disaster. I learned that the hard way when one of my test panes exploded into what felt like a million glittering shards.

But that accident was just one part of a much bigger journey: 30,000+ individual UV laser test runs across multiple glass types.

What started as a quest for clean results quickly turned into a deep dive into laser behavior, physics, and tolerances. The good news? You don’t need to burn thousands of hours or panes—I’ve done the legwork for you.

Ниже, I’ll walk you through the six most critical engraving variables, the exact settings that consistently delivered the best results, and a few powerful pro tips that can turn your average engraving into a showpiece.

---

Why UV Lasers Beat CO₂ for Glass Engraving

Both UV and CO₂ lasers can engrave glass, но difference in quality is stark.

• CO₂-лазеры work by thermal fracturing. They deliver powerful infrared heat that causes micro-cracks and chips—acceptable for industrial uses, but rarely pretty.
• УФ лазеры, by contrast, operate at a much shorter wavelength (355нм), which allows them to interact with glass at a photochemical level. This means:
  • Smoother, frosted finishes (similar to sandblasting)
  • Sharper lines and better definition
  • Reduced risk of fractures or thermal stress

---

The 6 Essential UV Laser Settings for Glass

To get pro-level results, there are six key settings you need to understand and optimize:

1. Скорость
2. Q-Пульс
3. Частота
4. Линейный интервал
5. Количество проходов
6. Фокус

Let’s break down each one and see what the tests revealed.

---

1. Скорость

Speed controls how fast the laser moves across your design. You’d think faster is better—but on glass, slower usually wins.

• Block (Filled) Engravings:
  Stick to 200–300 mm/s for a solid, consistent frost.
• Outline Work:
  Drop to 60–80 mm/s to ensure full marking along thinner paths.
• Glass Type Variation:
  • Закаленное стекло: Handles speeds up to 400 мм/с without losing fidelity.
  • Standard Window Glass: Often requires 100–250 mm/s for optimal clarity.

Кончик: Always test on a scrap first. Speed tolerance can vary based on your specific glass composition and any coatings.

---

2. Q-Пульс

Think of Q-Пульс as controlling the intensity of the energy burst delivered with each laser pulse.

• Lower values (1–2): Sharper, deeper engraves.
• Higher values (>5): Softer, more delicate touch.

🛠 Recommended Setting: Q-Pulse = 1 или 2
These settings gave the most consistent and frosted results across all my test samples.

---

3. Частота

This refers to how many pulses per second your laser delivers (measured in kHz). It directly affects how smooth the engraving appears.

• Низкая частота (20–25 kHz): Strong but rough results—prone to “dotted” текстура.
• Высокая частота (35–40 кГц): Smooth tones, but risk of weak, patchy engraving.

Ideal Range: 30–35 kHz

This sweet spot balances power and finesse for clean, sandblasted finishes without overburning or skipping.

---

4. Линейный интервал

This determines how tightly packed your scan lines are during a fill.

• Too Wide (>0.01 мм): Inconsistent coverage, banding, or patchiness.
• Too Tight (<0.002 мм): Beautiful results—but extremely slow jobs.

Best Range: 0.008–0.002 mm per line

Pro Trick:
В 0.001 мм, the engraving creates a raised, embossed effect with a solid white finish—almost like etched milk glass. Однако, it’s 4× slower than standard settings. Use for high-end projects.

---

5. Количество проходов

More passes = deeper engrave. But it doesn’t always mean better.

• 1 Проходить: Sufficient for most applications if your other settings are dialed in.
• 2–3 Passes: Useful for deeper texture or touchable depth, but not necessary for clarity.

Caution: On закаленное стекло, too many passes can structurally weaken the pane and lead to breakage—like my poor, shattered test piece.

---

6. Фокус

Getting your focus distance right is crucial.

• Optimal Focal Distance: Sharpest, cleanest engraving
• ±2 mm Offset: Still workable, but edges start to soften.
• ±4 mm or more: Expect patchy or faded results.

For Cylindrical Objects (Without a Rotary):
Set your focal point about 1 мм below the surface. This allows more vertical reach around the curve for better coverage.

---

Pro Tips to Save Time and Glass

1. Elevate Flat Pieces

Always lift flat glass slightly off the bed. If the beam passes through, it might engrave the underside of your piece—or worse, your machine bed.

Use small spacers, coins, or scrap acrylic.

---

2. Fix Mistakes Without Re-engraving the Whole Job

Made a tiny flaw or missed a section?

• Select the area in LightBurn
• Rotate the scan angle 180°
• Run that piece again

Since glass doesn’t darken with more passes, этот refresh pass blends in seamlessly.

---

3. Account for Glass Warp

Large glass panes aren’t perfectly flat. In LightBurn, use the Z-offset tools или split your design into segments with varied focal distances.

This helps maintain consistent quality edge-to-edge.

---

Cold-Start Settings (When You Only Get One Shot)

If I had zero time to test and only one attempt, these are the settings I’d go with:

Параметр	Ценить
Скорость	300 мм/с
Q-Пульс	1
Частота	32 кГц
Линейный интервал	0.005 мм
Проходы	1
Фокус	At exact focal point (±0 mm)

---

Glass engraving doesn’t have to be a painful guessing game. With the right UV laser and properly tuned settings, you can produce clean, professional-quality work—even without specialized sandblasting gear or rotary attachments.

Every piece of shattered glass I went through was worth it if it saves you time, материал, and frustration.

---

Interested in the UV laser I used for testing?
Я использовал Omni One UV Laser, and you can find discount links and codes in the description if you’re thinking of adding one to your shop.