接地良好后，打开本设备的电源. ONLY use this device with one hand at a time.
激光器由极高的电压连接供电，在操作过程中将两只手同时放在机器上，有可能与人体形成闭合电路,导致触电. 激光雕刻机周围的区域应保持干燥, 通风良好, 并通过环境控制将环境温度保持在 40–95°F 之间 (5–35°C). The ambient humidity should not exceed 70%.

ComMarker B4 光纤激光雕刻机组装指南

使用 ComMarker B4 光纤激光雕刻机非常简单. Just follow the eight steps below to complete the process.

1. 将零件放在桌子上

首先拆开所有组件的包装 ComMarker B4 光纤激光雕刻机. 将它们放在干净的地方, flat surface to ensure you have all the necessary parts and tools before starting the assembly.

2. 将联轴器放置在轴的正确位置

找到激光雕刻机上的轴. 确保它紧贴在指定位置. 联轴器对于连接电机和激光头至关重要, allowing precise movements during operation.

3. 用镶嵌螺钉紧固联轴器

一旦联轴器就位, 使用提供的镶嵌螺钉将其紧固. This ensures the coupling stays firmly attached to the shaft during the engraving process.

4. 用螺丝固定支撑杆

下一个, 将支撑杆垂直放置在机器底座上. 使用提供的螺钉牢固地固定杆. This pole supports the laser head and ensures stability during operation.

5. 将激光头放在支撑架上，拧紧螺丝固定激光头

小心地将激光头放置在支撑架上. 正确对齐并使用提供的螺钉将激光头固定到支撑架上. Make sure the laser head is securely fixed to avoid any movement during engraving.

6. 将垫圈放在杆的顶部, 绕丝杠旋转

取出垫圈并将其放置在支撑杆的顶部, 确保它围绕丝杠. The gasket helps reduce vibration and ensures smooth movement of the laser head along the pole.

7. 用螺丝和垫圈固定手摇手柄

将手摇曲柄安装到机器上. 使用螺钉和垫圈将其固定到位. 手摇手柄允许手动调节激光头位置, providing precision and control during setup and operation.

8. 将激光机与计算机连接并打开机器

最后, 使用提供的电缆将 ComMarker B4 光纤激光雕刻机连接到计算机. 确保所有连接都是安全的. 连接后, 打开机器. 按照软件说明完成设置并开始使用 your laser engraver.

ComMarker B4 光纤激光雕刻机: 辅助支架的组装

分步组装指南

1. 将零件放在桌子上

首先将辅助支架的所有部件放在干净的地方, 平坦的表面. Ensure you have all the necessary components and tools before beginning the assembly.

2. 用螺丝连接金属棒和大环

拿起金属棒并将其与大环对齐. 使用提供的螺钉将金属棒牢固地固定到大环上. This connection forms the primary structure of the auxiliary holder.

3. 用螺丝固定金属条和小环

下一个, 使用螺钉将小环固定到金属杆上. Ensure the small ring is securely fixed to provide stability to the auxiliary holder.

4. 用螺钉将固定环固定到激光头上

将固定环放置在激光头周围. 使用螺钉将项圈牢固固定. This step is essential to ensure the auxiliary holder is correctly aligned with the laser head.

5. 将另一个小环拧到固定环上

取下另一个小环并将其拧到固定环上. This additional ring helps stabilize the auxiliary holder and ensures precise positioning.

6. 如下所示将组装好的零件拧上

按照 ComMarker B4 光纤激光雕刻机随附的装配图将组装好的零件拧在一起. Ensure all components are tightly secured to maintain the holder’s stability.

7. 根据焦距调节辅助支架高度

调整辅助支架的高度以匹配激光雕刻机的焦距. This step is crucial to achieve the correct focal point for precise engraving.

8. 拧紧小环以将辅助支架固定在正确的焦点处

调整好高度后, 拧紧小环以将辅助支架锁定到位. Ensure the holder is fixed at the correct focus point to optimize engraving accuracy.

如何安装光纤激光雕刻机的驱动程序?

1.安装驱动程序

笔记: 安装驱动前请进行以下操作
1) 机器已开机;

2) 保持紧急按钮未被按下;

3) 数据线已连接

1. 打开设备管理

首先右键单击 “这台电脑” 或者 “我的电脑” 在桌面或文件资源管理器中. 从上下文菜单, 选择 “管理” to open the Computer Management window.

2. 访问设备管理器

在计算机管理窗口中, 点击 “装置经理” 在左侧窗格中. This will display a list of all the hardware devices connected to your computer.

3. 找到设备

在设备管理器中, 寻找“USBLMCV2”, “USBLMCV4”, 或“其他设备”或“通用串行总线设备”下的“未知设备”. These entries represent your fiber laser engraver that needs the driver installed.

4. 更新驱动程序

右键单击“USBLMCV2”, “USBLMCV4”, 或“未知设备”并选择 “更新驱动程序” from the context menu.

5. 浏览驱动程序

在更新驱动程序软件窗口中, 选择 “浏览我的计算机以查找驱动程序”. This option allows you to manually select the driver files from your computer.

6. 找到驱动程序文件

将光纤激光雕刻机随附的 USB 驱动器插入计算机. 在文件资源管理器中导航到 USB 驱动器，找到包含与您的 Windows 系统对应的驱动程序文件的文件夹. 选择该文件夹并单击 “好的”.

7. 安装驱动程序

点击 “安装” 开始驱动程序安装过程. Follow any additional on-screen instructions to complete the installation.

8. 完成安装

一旦安装成功, 点击“完成”. 你现在应该看到 “北京金城装置” 列在设备管理器下, indicating that the driver has been installed correctly.

著名的: *建议将U盘的文件复制粘贴到电脑桌面或其他电脑磁盘上. *如果驱动安装不成功, please refer to FAQ 1

2. 打开软件

1. 访问 USB 文件夹:
   • 打开您的 USB 文件夹 光纤激光雕刻机.
   • 导航至 “ComMarker 的 EZCAD” folder.
   • 如果你的镜头是110mm, select the 110mm folder.
2. 启动 EZCAD2:
   • Open the software “EZCAD2” from the selected folder.
   • 您可以输入 “文本”, 进口 “图片” 或者 “矢量文件”. 用于初始测试, it is recommended to select and test with text.

3. 导入修正文件

1. 打开参数设置:
   • 在EZCAD2中, 选择 “范围 (F3)”.
   • 打钩 “使用正确的文件”.
2. 选择修正文件:
   • 从 USB 闪存驱动器中选择以 .cor 结尾的文件 (或者已经复制到电脑磁盘的文件).
   • 点击 “好的 (确认)” to apply the correction file.

4. 调整焦点

1. 找到最佳焦点:
   • Use the up or down buttons to lift or lower the laser head until the three red light points overlap.
   • The point where these three red lights overlap is the optimal focal point for engraving.
2. 测量焦距:
   • 本机的测量焦距是特定于镜头的:
     • 110毫米镜头: _______ 毫米
     • 200毫米镜头: _______ 毫米
   • 测量距离是激光头底线到雕刻材料表面的长度. 该参数为手动测量, and each device may have different focal lengths due to variations in laser sources and field lenses.

笔记: 机器出厂前, 我们已经做了红灯校正 (适用于110mm镜头). 三个红色光点重叠的位置, 激光发出最强的光. 然而, 由于交通原因, 您收到的红灯的焦点可能会移动, 并且焦点不会是最佳焦距. 请按以下步骤操作:

1. 放置不锈钢测试板

1. 放置测试板:
   • Place the stainless steel test plate on the machine table.

2. 调整激光头

1. 找到最佳焦点:
   • 提升或降低激光头至最佳焦点, as indicated by the handwritten number provided.

3. 打开机器并连接

1. 开机并连接:
   • Turn on the machine.
   • Connect the machine to the computer.

4. 导入文本进行测试

1. 负载测试参数:
   • Import the “TEXT” file for testing into the software.
   • Select the default parameters.
   • Tick the “continuous part” button.

5. 测试标记

1. 检查标记区域:
   • 按“红 (F1)” to ensure the marking area aligns with the test material.
   • Click “mark” to start continuous marking with the laser.

6. 调整激光强度

1. 优化激光强度:
   • 当激光打标时, lift or lower the laser head.
   • Observe the change in laser beam intensity.
   • Stop adjusting when the laser works with the strongest beam.

7. 对准辅助红灯

1. 松开螺丝:
   • Loosen the screws for the two beams of the auxiliary red light.
2. 重叠的红光点:
   • Manually adjust the relative position of the red light dots to make them overlap.

8. 确保职位

手动调整红光点的相对位置，使它们重叠. 并拧紧螺丝

5.评分测试

1. 准备材料:
   • Place the test engraving material on the machine.
2. 检查标记区域:
   • 点击 “红色的 (F1)” to ensure the marking area aligns with the test material.
3. 开始标记:
   • Tick “Default Parameters”.
   • 点击 “标记 (F2)” to start marking.

参数

配件

常问问题: 光纤激光雕刻机 ComMarker B4

Q1: 驱动安装不成功?

1. 检查您的 Windows 系统: 确保您使用的是经过许可的 Windows 系统. 如果不, try using another computer.
2. 更换数据线: Use a magnetic-proof data cable for better results.
3. 检查 USB 端口: 台式机机箱上的前置 USB 端口经常损坏. Try using rear USB ports or another computer.
4. 机器状态: 确保机器已开启, 紧急按钮未被按下, and the data cable is properly connected.
5. 联系支持人员: 如果问题仍然存在, contact after-sales support or email us.

Q2: The driver in the device manager is different from the instruction in this manual.

• 冲突的驱动程序: 如果另一个驱动程序会出现此问题, 例如 LightBurn 驱动程序, 已安装. Uninstall the incorrect driver and delete it.

第三季度: The USB flash drive is damaged and cannot be opened.

• 从网站下载: Visit ComMarker’s official website to download the B4 driver and software.
• 联系支持人员: Email the after-sales team for assistance.

第四季度: 红光预览适用于矩形, but there is no mark or the marks are very light.

• 调整焦距: 参考步骤 4 of the operation instructions for adjusting the focal length.
• 联系支持人员: 如果问题仍然存在, email the after-sales team.

Q5: 找不到加密狗, 软件在演示模式下运行, or fails to open the LMC driver.

• 检查连接: Ensure the machine is powered on and connected to the computer via the data cable.

Q6: 向上和向下按钮不起作用; the machine does not move when pressing the button.

• 调整联轴器: Readjust the angle of the coupling and refix it with screws.

Q7: 预览和雕刻区域的尺寸与软件中的尺寸不一致, 红光预览与实际雕刻位置不一致, or the preview and the mark are not horizontal or vertical but angled.

1. 导入校准文件: 使用机器附带的 USB 驱动器中的校准文件. 参考步骤 3 of the operating instructions.
2. 手动调节: 选择 “范围 (F3)”, 然后 “其他” 和 “红光指针”. 输入数字 “偏移 X” 和 “偏移 Y” based on the actual deviation.
3. 联系支持人员: 如果问题仍然存在, contact the after-sales team by email.

Q8: 如何在软件中更改物理标记区域?

• 调整字段参数: 点击 “范围 (F3)”, 然后选择 “场地”. 输入数字 “偏移 X”, “偏移 Y”, 或者 “角度” based on measurements with a ruler.

Q9: Some of the engraving areas are clear while others are light.

洁净场镜头: 确保场镜清洁. 如果脏了, clean it carefully.

检查光路: 确保光路前后水平. Loosen and refix the screws connecting the column and the optical path.

确保垂直度: Ensure the oval base of the pole is perpendicular to the pole.

拧紧螺丝: Re-tighten the screws of the metal parts supporting the optical path.

Q10: There is only one dot of preview and marking laser.

• 检查检流计功率: 拆下光路上的盖子，检查DB15或DB25电缆是否断开. Reconnect if necessary.

Q11: 预览红灯不清晰, or there is no preview red light.

• 调整红色光源: 取下激光头盖, 手动调节红光源, 移动并再次修复, or disassemble and reinstall.

Q12: Nothing displays on the canvas board when importing text or pictures.

• 中心内容: Click the practical center button to center the picture and text on the canvas.

Q13: 激光变弱, and the engraving effect worsens.

1. 洁净场镜头: 用干净的布清洁场镜. 如果打标时未取下镜头盖, it can cause pollution and weaker laser performance.
2. 更换场镜: 如果场镜污染太严重, it may need to be replaced.

Q14: 哪个版本的 LightBurn 软件适合 ComMarker B4?

• 现有许可证: Purchase the “Add Galvo devices to existing license key” if you already have the software for a gantry type.
• 新许可证: 选择“LightBurn- Galvo license key” if you haven’t bought any license yet.